|
U-Boot 1.1.3 (Apr 15 2016 - 17:46:32)
Board: Ralink APSoC DRAM: 128 MB
Power on memory test. Memory size= 128 MB...OK!
relocate_code Pointer at: 87fb8000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
!!! nand page size = 2048, addr len=4
..============================================
Ralink UBoot Version: 4.2.S.1
--------------------------------------------
ASIC 7620_MP (Port5None)
DRAM_CONF_FROM: Auto-detection
DRAM_TYPE: DDR2
DRAM component: 1024 Mbits
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: NAND Flash
Date:Apr 15 2016 Time:17:46:32
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =128 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
3: System Boot system code via Flash.
Booting System 2
..ranand_erase_write: offs:40000, count:20000
.Done!
done
## Booting image at bc600000 ...
Image Name: MIPS OpenWrt Linux-2.6.36
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2284520 Bytes = 2.2 MB
Load Address: 80000000
Entry Point: 80000000
................................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
commandline uart_en=0 factory_mode=0 mem=128m
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
LINUX started...
THIS IS ASIC
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.36 (jenkins@JenkinsServer) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Fri Apr 15 17:59:34 CST 2016
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 580 MHz
[ 0.000000] PCIE: bypass PCIe DLL.
[ 0.000000] PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
[ 0.000000] disable all power about PCIe
[ 0.000000] CPU revision is: 00019650 (MIPS 24Kc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 uart_en=0 factory_mode=0 mem=128m
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00078fdb
[ 0.000000] Readback ErrCtl register=00078fdb
[ 0.000000] allocated 655360 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 123760k/131072k available (3348k kernel code, 7312k reserved, 1028k data, 868k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled
[ 0.010000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.220000] pid_max: default: 32768 minimum: 301
[ 0.220000] Mount-cache hash table entries: 512
[ 0.220000] Initializing cgroup subsys cpuacct
[ 0.230000] Initializing cgroup subsys memory
[ 0.230000] Initializing cgroup subsys net_cls
[ 0.230000] devtmpfs: initialized
[ 0.240000] NET: Registered protocol family 16
[ 0.240000] RALINK_GPIOMODE = 121b1c
[ 0.240000] RALINK_GPIOMODE = 101b1c
[ 0.440000] PPLL_CFG1=0xe6c000
[ 0.450000] MT7620 PPLL lock
[ 0.450000] PPLL_DRV =0x80080504
[ 0.650000] Deassert the PCIE0 RESET.
[ 0.650000] start PCIe register access
[ 1.150000] RALINK_RSTCTRL = 2400000
[ 1.160000] RALINK_CLKCFG1 = 75afffc0
[ 1.160000]
[ 1.160000] *************** MT7620 PCIe RC mode *************
[ 1.660000] PCIE0 enabled
[ 1.670000] init_rt2880pci done
[ 1.670000] bio: create slab at 0
[ 1.680000] SCSI subsystem initialized
[ 1.680000] usbcore: registered new interface driver usbfs
[ 1.680000] usbcore: registered new interface driver hub
[ 1.690000] usbcore: registered new device driver usb
[ 1.690000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.700000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 1.700000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[ 1.710000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[ 1.710000] pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
[ 1.720000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[ 1.720000] pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] (PCI address [0x20000000-0x200fffff]
[ 1.730000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[ 1.730000] pci 0000:00:00.0: PCI bridge to [bus 01-01]
[ 1.740000] pci 0000:00:00.0: bridge window [io disabled]
[ 1.740000] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 1.750000] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref]
[ 1.750000] BAR0 at slot 0 = 0
[ 1.760000] bus=0x0, slot = 0x0
[ 1.760000] res[0]->start = 0
[ 1.760000] res[0]->end = 0
[ 1.760000] res[1]->start = 20200000
[ 1.770000] res[1]->end = 2020ffff
[ 1.770000] res[2]->start = 0
[ 1.770000] res[2]->end = 0
[ 1.770000] res[3]->start = 0
[ 1.780000] res[3]->end = 0
[ 1.780000] res[4]->start = 0
[ 1.780000] res[4]->end = 0
[ 1.780000] res[5]->start = 0
[ 1.790000] res[5]->end = 0
[ 1.790000] bus=0x1, slot = 0x0
[ 1.790000] res[0]->start = 20000000
[ 1.790000] res[0]->end = 200fffff
[ 1.800000] res[1]->start = 0
[ 1.800000] res[1]->end = 0
[ 1.800000] res[2]->start = 0
[ 1.800000] res[2]->end = 0
[ 1.810000] res[3]->start = 0
[ 1.810000] res[3]->end = 0
[ 1.810000] res[4]->start = 0
[ 1.810000] res[4]->end = 0
[ 1.820000] res[5]->start = 0
[ 1.820000] res[5]->end = 0
[ 1.820000] Switching to clocksource MIPS
[ 1.830000] NET: Registered protocol family 2
[ 1.830000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 1.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.850000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.850000] TCP: Hash tables configured (established 4096 bind 4096)
[ 1.860000] TCP reno registered
[ 1.860000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.870000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.870000] NET: Registered protocol family 1
[ 2.570000] RT3xxx EHCI/OHCI init.
[ 2.580000] msgmni has been set to 241
[ 2.580000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 2.590000] io scheduler noop registered (default)
[ 2.600000] RALINK_REG_PIO7140DATA b0000670 = 0
[ 2.700000] RALINK_REG_PIO7140DATA b0000670 = 2000000
[ 2.710000] Ralink gpio driver initialized
[ 2.710000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 2.720000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
[ 2.720000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
[ 2.730000] init reset module!
[ 2.740000] brd: module loaded
[ 2.740000] !!! nand page size = 2048, addr len=4
[ 2.750000] ra_nand_init: alloc 1350, at 87fd0000 , btt(87fd10c0, 100), ranfc_mtd:87fd11c0
[ 2.760000] Creating 13 MTD partitions on "ra_nfc":
[ 2.760000] 0x000000000000-0x000008000000 : "ALL"
[ 2.790000] 0x000000000000-0x000000040000 : "Bootloader"
[ 2.800000] 0x000000040000-0x000000080000 : "Config"
[ 2.810000] 0x000000080000-0x0000000c0000 : "Bdata"
[ 2.810000] 0x0000000c0000-0x000000100000 : "Factory"
[ 2.820000] 0x000000100000-0x000000140000 : "crash"
[ 2.820000] 0x000000140000-0x000000180000 : "crash_syslog"
[ 2.830000] 0x000000180000-0x000000200000 : "reserved0"
[ 2.840000] 0x000000200000-0x000000600000 : "kernel0"
[ 2.840000] 0x000000600000-0x000000a00000 : "kernel1"
[ 2.850000] 0x000000a00000-0x000002a00000 : "rootfs0"
[ 2.850000] 0x000002a00000-0x000004a00000 : "rootfs1"
[ 2.860000] 0x000004a00000-0x000008000000 : "overlay"
[ 2.870000] rdm_major = 253
[ 2.870000] SMACCR1 -- : 0x000034ce
[ 2.870000] SMACCR0 -- : 0x004b3cc1
[ 2.880000] Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500!
[ 2.890000] SMACCR1 -- : 0x000034ce
[ 2.890000] SMACCR0 -- : 0x004b3cc1
[ 2.900000] PROC INIT OK!
[ 2.900000] PPP generic driver version 2.4.2
[ 2.900000] PPP MPPE Compression module registered
[ 2.910000] NET: Registered protocol family 24
[ 2.910000] PPTP driver version 0.8.5
[ 2.920000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.040000] rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
[ 3.050000] rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
[ 3.090000] rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
[ 3.110000] rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
[ 3.110000] hub 1-0:1.0: USB hub found
[ 3.120000] hub 1-0:1.0: 1 port detected
[ 3.120000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.150000] rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
[ 3.150000] rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
[ 3.160000] rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
[ 3.230000] hub 2-0:1.0: USB hub found
[ 3.230000] hub 2-0:1.0: 1 port detected
[ 3.240000] usbcore: registered new interface driver cdc_acm
[ 3.240000] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[ 3.250000] Initializing USB Mass Storage driver...
[ 3.260000] usbcore: registered new interface driver usb-storage
[ 3.260000] USB Mass Storage support registered.
[ 3.270000] usbcore: registered new interface driver usbserial
[ 3.270000] USB Serial support registered for generic
[ 3.280000] usbcore: registered new interface driver usbserial_generic
[ 3.290000] usbserial: USB Serial Driver core
[ 3.290000] USB Serial support registered for pl2303
[ 3.300000] usbcore: registered new interface driver pl2303
[ 3.300000] pl2303: Prolific PL2303 USB to serial adaptor driver
[ 3.310000] USB Serial support registered for TI USB 3410 1 port adapter
[ 3.320000] USB Serial support registered for TI USB 5052 2 port adapter
[ 3.320000] usbcore: registered new interface driver ti_usb_3410_5052
[ 3.330000] ti_usb_3410_5052: v0.10:TI USB 3410/5052 Serial Driver
[ 3.340000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
[ 3.340000] u32 classifier
[ 3.350000] input device check on
[ 3.350000] Actions configured
[ 3.350000] Netfilter messages via NETLINK v0.30 with ipset netlink.patch.
[ 3.360000] nf_conntrack version 0.5.0 (1933 buckets, 7732 max)
[ 3.370000] xt_time: kernel timezone is -0000
[ 3.370000] GRE over IPv4 demultiplexor driver
[ 3.380000] ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
[ 3.390000] TCP cubic registered
[ 3.390000] NET: Registered protocol family 10
[ 3.400000] NET: Registered protocol family 17
[ 3.400000] L2TP core driver, V2.0
[ 3.400000] PPPoL2TP kernel driver, V2.0
[ 3.410000] L2TP netlink interface
[ 3.410000] 802.1Q VLAN Support v1.8 Ben Greear
[ 3.420000] All bugs added by David S. Miller
[ 3.440000] Freeing unused kernel memory: 868k freed
[ 3.530000] Loading essential drivers...
[ 3.530000] Press Ctrl+C to enter RAMFS...
[ 4.550000] Check for USB recovery...
[ 4.580000] Bringup the system...
[ 4.590000] flag_boot_rootfs=1 mounting /dev/mtd11
[ 4.600000] UBI: attaching mtd11 to ubi0
[ 4.600000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 4.610000] UBI: logical eraseblock size: 126976 bytes
[ 4.610000] UBI: smallest flash I/O unit: 2048
[ 4.620000] UBI: VID header offset: 2048 (aligned 2048)
[ 4.620000] UBI: data offset: 4096
[ 4.780000] UBI: max. sequence number: 2
[ 4.790000] UBI: attached mtd11 to ubi0
[ 4.790000] UBI: MTD device name: "rootfs1"
[ 4.800000] UBI: MTD device size: 32 MiB
[ 4.800000] UBI: number of good PEBs: 256
[ 4.810000] UBI: number of bad PEBs: 0
[ 4.810000] UBI: max. allowed volumes: 128
[ 4.820000] UBI: wear-leveling threshold: 4096
[ 4.820000] UBI: number of internal volumes: 1
[ 4.830000] UBI: number of user volumes: 1
[ 4.830000] UBI: available PEBs: 0
[ 4.840000] UBI: total number of reserved PEBs: 256
[ 4.840000] UBI: number of PEBs reserved for bad PEB handling: 4
[ 4.850000] UBI: max/mean erase counter: 2/1
[ 4.850000] UBI: image sequence number: 1481461889
[ 4.860000] UBI: background thread "ubi_bgt0d" started, PID 80
UBI device number 0, total 256 LEBs (32505856 bytes, 31.0 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 4.950000] UBIFS: mounted UBI device 0, volume 0, name "system"
[ 4.950000] UBIFS: mounted read-only
[ 4.960000] UBIFS: file system size: 30093312 bytes (29388 KiB, 28 MiB, 237 LEBs)
[ 4.960000] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[ 4.970000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 4.980000] UBIFS: default compressor: zlib
[ 4.980000] UBIFS: reserved for root: 0 bytes (0 KiB)
config core 'version'
# ROM ver
option ROM '2.11.20'
# channel
option CHANNEL 'stable'
# hardware platform R1AC or R1N etc.
option HARDWARE 'R3'
# CFE ver
option UBOOT '1.0.2'
# Linux Kernel ver
option LINUX '0.1.12'
# RAMFS ver
option RAMFS '0.1.12'
# SQUASHFS ver
option SQAFS '0.1.12'
# ROOTFS ver
option ROOTFS '0.1.12'
#build time
option BUILDTIME 'Fri, 15 Apr 2016 17:43:41 +0800'
#build timestamp
option BUILDTS '1460713422'
#build git tag
option GTAG 'commit dec2379967c2b44760bc6bab36c584cf58e06ae4'
mount: mounting proc on /proc failed: Device or resource busy
mount: mounting sysfs on /sys failed: Device or resource busy
[ 5.760000] Raeth v3.0 (Tasklet,SkbRecycle)
[ 5.760000]
[ 5.760000] phy_tx_ring = 0x07ef6000, tx_ring = 0xa7ef6000
[ 5.760000]
[ 5.760000] phy_rx_ring0 = 0x07ef7000, rx_ring0 = 0xa7ef7000
[ 5.760000] SMACCR1 -- : 0x000034ce
[ 5.760000] SMACCR0 -- : 0x004b3cc1
[ 5.790000] ESW: Link Status Changed - Port4 Link UP
[ 5.790000] CDMA_CSG_CFG = 81000000
[ 5.790000] GDMA1_FWD_CFG = 20710000
- preinit -
Fri Apr 15 17:59:34 UTC 2016
- regular preinit -
[ 5.950000] UBI: attaching mtd12 to ubi1
[ 5.960000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 5.960000] UBI: logical eraseblock size: 126976 bytes
[ 5.970000] UBI: smallest flash I/O unit: 2048
[ 5.970000] UBI: VID header offset: 2048 (aligned 2048)
[ 5.980000] UBI: data offset: 4096
[ 6.230000] UBI: max. sequence number: 586
[ 6.240000] UBI: attached mtd12 to ubi1
[ 6.250000] UBI: MTD device name: "overlay"
[ 6.250000] UBI: MTD device size: 54 MiB
[ 6.260000] UBI: number of good PEBs: 432
[ 6.260000] UBI: number of bad PEBs: 0
[ 6.270000] UBI: max. allowed volumes: 128
[ 6.270000] UBI: wear-leveling threshold: 4096
[ 6.280000] UBI: number of internal volumes: 1
[ 6.280000] UBI: number of user volumes: 1
[ 6.290000] UBI: available PEBs: 0
[ 6.290000] UBI: total number of reserved PEBs: 432
[ 6.300000] UBI: number of PEBs reserved for bad PEB handling: 8
[ 6.300000] UBI: max/mean erase counter: 2/1
[ 6.310000] UBI: image sequence number: 520187673
[ 6.310000] UBI: background thread "ubi_bgt1d" started, PID 149
UBI device number 1, total 432 LEBs (54853632 bytes, 52.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 6.360000] UBIFS: recovery needed
[ 6.420000] UBIFS: recovery completed
[ 6.420000] UBIFS: mounted UBI device 1, volume 0, name "data"
[ 6.430000] UBIFS: file system size: 52187136 bytes (50964 KiB, 49 MiB, 411 LEBs)
[ 6.440000] UBIFS: journal size: 2666496 bytes (2604 KiB, 2 MiB, 21 LEBs)
[ 6.440000] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 6.450000] UBIFS: default compressor: lzo
[ 6.450000] UBIFS: reserved for root: 2464926 bytes (2407 KiB)
/lib/preinit.sh: line 1: jffs2_not_mounted: not found
- init -
[ 7.080000] ra2880stop()...Done
[ 7.100000] Free TX/RX Ring Memory!
init started: BusyBox v1.19.4 (2016-04-15 17:38:14 CST)
Please press Enter to activate this console. rcS S boot: INFO: rc script run time limit to 65 seconds.
[ 8.040000] tntfs: module license 'Commercial. For support email [email protected].' taints kernel.
[ 8.050000] Disabling lock debugging due to kernel taint
[ 8.090000] Tuxera NTFS driver 3015.1.29 [Flags: R/W MODULE].
[ 8.190000] Tuxera FAT 12/16/32 driver version 3014.1.24 [Flags: R/W MODULE].
[ 8.250000] tun: Universal TUN/TAP device driver, 1.6
[ 8.260000] tun: (C) 1999-2004 Max Krasnyansky
[ 8.280000] Mirror/redirect action on
[ 8.550000] GRE over IPv4 tunneling driver
[ 8.780000] ipt: xt_cgroup_MARK installed ok.
[ 8.850000] ip_set: protocol 6
[ 9.140000] sstack_init
[ 10.430000] |