DSPLE000

DSPLE000 Product Manual

The DSPLE000 was designed to act as a nexus for industrial data collection and management. With three built in serial ports and a 10 Base-T/100 Base-TX Ethernet port, the unit performs protocol conversion, allowing disparate devices to communicate seamlessly with one another. The Ethernet port supports up to ten protocols simultaneously using Crimson 3, so even Ethernet to Ethernet conversion may be performed.

The CompactFlash card allows new configuration files to be loaded into the DSPLE000. The USB port may be used for blazing fast file downloads, or to mount the CompactFlash card as an external drive to your PC. The Data Station’s DIN rail mounting saves time and panel space and snaps easily onto standard top hat (T) profile DIN rail

SOFTWARE The DSPLE000 is programmed with Crimson 2.0 or Crimson 3.0 software for Windows® 2000 or later platforms. The software is an easy to use graphical interface which can be purchased as part of a kit that includes a manual and cables, or downloaded free of charge from www.redlion.net.

POWER: 24 VDC ± 10% 200 mA min., without expansion card 1 Amp maximum with expansion card fitted Must use NEC Class 2 or Limited Power Source (LPS) rated power supply.

COMMUNICATIONS: USB/PG Port: Adheres to USB specification 1.1. Device only using Type B connection. Serial Ports: Format and Baud Rates for each port are individually software programmable up to 115,200 baud. RS232/PG Port: RS232 port via RJ12 COMMS Ports: RS422/485 port via RJ45, and RS232 port via RJ12 DH485 TXEN: Transmit enable; open collector, VOH = 15 VDC, VOL = 0.5 V @ 25 mA max. Ethernet Port: 10 BASE-T / 100 BASE-TX RJ45 jack is wired as a NIC (Network Interface Card)

LEDs: STS – Status LED indicates condition of Data Station. TX/RX – Transmit/Receive LEDs show serial activity. Ethernet – Link and activity LEDs. CF – CompactFlash LED indicates card status and read/write activity

MEMORY: On-board User Memory: 4 Mbytes of non-volatile Flash memory. On-board SDRAM: 2 Mbytes Memory Card: CompactFlash Type II slot for Type I and Type II cards. Used for optional database storage only

REAL-TIME CLOCK: Typical accuracy is less than one minute per month drift. Battery: Lithium Coin Cell. Typical lifetime of 10 years at 25 ºC. A “Battery Low” system variable is available so that the programmer can choose specific action(s) to occur when the battery voltage drops below its nominal voltage. This unit is NOT field serviceable. All work must be done by a qualified technician.

ENVIRONMENTAL CONDITIONS: Operating Temperature Range: DSPLE000: 0 to 50 °C Storage Temperature Range: -30 to 70 °C Operating and Storage Humidity: 80% max relative humidity, non-condensing, from 0 to 50 °C Vibration to IEC 68-2-6: Operational 5 to 150 Hz, 2 g. Shock to IEC 68-2-27: Operational 30 g Altitude: Up to 2000 meters

CONSTRUCTION: Case body is burgundy high impact plastic and stainless steel. For indoor use only. Installation Category II, Pollution Degree 2.

POWER CONNECTION: Removable wire clamp screw terminal block. Wire Gage Capacity: 24 AWG to 12 AWG Torque: 4.45 to 5.34 in/lb (0.5 to 0.6 N-m)

MOUNTING: Snaps onto standard DIN style top hat (T) profile mounting rails according to EN50022 -35 x 7.5 and -35 x 15.

CERTIFICATIONS AND COMPLIANCES: CE Approved EN 61326-1 Immunity to Industrial Locations Emission CISPR 11 Class A Safety requirements for electrical equipment for measurement, control, and laboratory use: EN 61010-1: General Requirements EN 61010-2-201: Particular Requirements for Control Equipment RoHS Compliant UL Listed: File #E302106 UL Hazardous: File #E317425 ABS Certificate #09-HS426719-B-4-PDA Refer to EMC Installation Guidelines section of the bulletin for additional information.

WEIGHT: 15.1 oz (428 g)

DSPLE Product Manual