查看AIX系统cpu、内存、网卡、硬盘、HBA卡信息命令

查看AIX系统的主机型号、序列号、CPU、内存、硬盘、网卡、网卡物理插槽位置信息、是否配置以太网通道、网卡链路状态、当前网络速率、HBA卡、HBA卡物理插槽位置信息、HBA卡WWN、HBA卡支持速率、HBA卡当前速率、VG、PV、LV信息、该主机当前由哪台HMC管理、配置了多少磁带机驱动器 tape driver等信息，可以通过一段脚本收集全部信息。一、查看型号、序列号、CPU、内存、HMC 型号：#uname -M IBM,8204-E8A 序列号：#uname -u IBM,0206***** CPU数量 #lsdev -Cc processor proc0 Available 00-00 Processor proc2 Available 00-02 Processor proc4 Available 00-04 Processor proc6 Available 00-06 Processor proc8 Available 00-08 Processor proc10 Available 00-10 Processor proc12 Available 00-12 Processor proc14 Available 00-14 Processor CPU主频#lsattr -El proc0 frequency 4204000000 Processor Speed False smt_enabled true Processor SMT enabled False smt_threads 2 Processor SMT threads False state enable Processor state False type PowerPC_POWER6 Processor type False 查看CPU是否64位#prtconf -c CPU Type: 64-bit 内存信息：#lsattr -El mem0 ent_mem_cap I/O memory entitlement in Kbytes False goodsize 63744 Amount of usable physical memory in Mbytes False mem_exp_factor Memory expansion factor False size 63744 Total amount of physical memory in Mbytes False var_mem_weight Variable memory capacity weight False 查看该机当前由哪台HMC管理 #lsrsrc IBM.ManagementServer Resource Persistent Attributes for IBM.ManagementServer resource 1: Name= "123.123.123.9" Hostname= "123.123.123.9" ManagerType= "HMC" LocalHostname= "123.123.234.132" ClusterTM= "9078-160" ClusterSNum= "" ActivePeerDomain = "" NodeNameList= {"testdb1"} 型号、序列号、内存统一信息：#lsattr -El sys0 fwversion IBM,EL350_085 Firmware version and revision levels False modelname IBM,8204-E8A Machine name False realmem 65273856 Amount of usable physical memory in Kbytes False systemid IBM,0206***** Hardware system identifier False二、查看磁盘信息： #lspv hdisk0 00cb01e637be5983 rootvg active hdisk1 00cb01e6dd9045e6 rootvg active#lspath Enabled hdisk0 sas0 Enabled hdisk1 sas0 Available ses0 sas0 Available ses1 sas0 列出所有磁盘设备#lsdev -Cc disk hdisk0 Available 02-08-00 SAS Disk Drive hdisk1 Available 02-08-00 SAS Disk Drive 查看磁盘容量#bootinfo -s hdisk0 140013 查看磁盘属性#lsattr -El hdisk0 reserve_policy no_reserve Reserve Policy True size_in_mb 146800 Size in Megabytes False 查看磁盘物理插槽信息#lscfg -vpl hdisk0 hdisk0 U78A0.001.DNWK9W6-P2-D3 SAS Disk Drive (146800 MB) Hardware Location Code......U78A0.001.DNWK9W6-P2-D3 以上命令适用于现场查看，需要查看哪些硬盘，就执行几条命令，但是当需要用户帮忙采集信息，而系统磁盘数量未知的情况下就难以胜任了，以下脚本列出本机所有磁盘信息并对每个磁盘执行bootinfo -s查看磁盘容量，执行lsattr -El查看磁盘属性、执行lscfg -vpl查看磁盘物理插槽、lspv查看磁盘pv信息等。

1.      echo "#lsdev -Cc disk"

2.      lsdev -Cc disk

3.      for i in `lsdev -Cc disk|awk '{print $1}'`;

4.      do

5.      echo "nInformation about "$i "n#bootinfo -s" $i

6.      bootinfo -s $i

7.      echo "n#lsattr -El" $i

8.      lsattr -El $i

9.      echo "n#lscfg -vpl " $i

10.  lscfg -vpl $i

11.  echo "n#lspv " $i

12.  lspv $i

13.  done

复制代码三、查看网卡信息 #lsdev -Cc adapter|grep ent ent0 Available Logical Host Ethernet Port (lp-hea) ent1 Available Logical Host Ethernet Port (lp-hea) ent2 Available 04-00 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003) ent3 Available 04-01 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003) ent4 Available EtherChannel / IEEE 802.3ad Link Aggregation 以上信息显示ent4通过以太网通道绑定后生成的网卡，执行lsattr -El ent4可以查看ent4由哪些网卡绑定而成，是主备模式、负载均衡模式或者负载均衡+主备模式。#lsattr -El ent4 adapter_names ent0 EtherChannel Adapters True auto_recovery yes Enable automatic recovery after failover True backup_adapter ent2 Adapter used when whole channel fails True mode standard EtherChannel mode of operation True netaddr 0 Address to ping True#lscfg -vpl ent2 ent2 U78A0.001.DNWK58T-P1-C1-T1 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003) Hardware Location Code......U78A0.001.DNWK58T-P1-C1-T1#lsattr -El en4 netaddr 123.123.123.61 Internet Address True netmask 255.255.255.128 Subnet Mask True state up Current Interface Status True#netstat -in #netstat -rn #ifconfig -a #ifconfig -l 查看网卡当前连接状态、链路速率#netstat -v en4 |grep -i Speed Media Speed Selected: Autonegotiate Media Speed Running: 1000 Mbps / 1 Gbps, Full Duplex External-Network-Switch (ENS) Port Speed: 1000 Mbps / 1 Gbps, Full Duplex Media Speed Selected: Auto negotiation Media Speed Running: 1000 Mbps Full Duplex 在网卡数量未知的情况下，可以采用以下脚本一次性收集所有网卡信息：

1.      echo "#lsdev -Cc adapter|grep ent"

2.      lsdev -Cc adapter|grep ent

3.      for i in `lsdev -Cc adapter|awk '{print $1}' |grep ent`;

4.      do

5.      echo "nInformation about "$i "n#lsattr -El" $i

6.      lsattr -El $i

7.      echo "n#lscfg -vl " $i

8.      lscfg -vl $i

9.      done

10.  for i in `ifconfig -l`;

11.  do

12.  echo "nInformation about "$i "n#lsattr -El" $i

13.  lsattr -El $i

14.  echo "n#netstat -v " $i

15.  netstat -v $i

16.  echo "n#netstat -v " $i "|grep -i Speed"

17.  netstat -v $i |grep -i Speed

18.  done

复制代码四、HBA卡信息 #lsdev -Cc adapter|grep fcs fcs0 Available 01-08 FC Adapter fcs1 Available 01-09 FC Adapter fcs2 Available 04-08 FC Adapter fcs3 Available 04-09 FC Adapter#lsattr -El fcs0 查看HBA卡的物理插槽、WWN：#lscfg -vpl fcs0 fcs0 U78A0.001.DNWK9W6-P1-C4-T1 FC Adapter Network Address.............10000000C9B54A92 Hardware Location Code......U78A0.001.DNWK9W6-P1-C4-T1 以上Network Address即为fcs0的WWN。 在HBA卡数量未知的情况下，可以采用以下脚本一次性收集所有HBA卡的物理插槽、WWN信息，这点项目中非常经常用到，因为需要收集HBA卡的WWN用于SAN交换机配置ZONE信息、存储端也需要WWN用于Mapping LUN：

1.      echo "#lsdev -Cc adapter|grep fcs"

2.      lsdev -Cc adapter|grep fcs

3.      for i in `lsdev -Cc adapter|grep fcs|awk '{print $1}'`;

4.      do

5.      echo "nInformation about "$i "n#lsattr -El" $i

6.      lsattr -El $i

7.      echo "n#lscfg -vpl " $i

8.      lscfg -vl $i

9.      echo "n#fcstat " $i

10.  fcstat $i

11.  done

复制代码五、磁带tape信息 #lsdev -Cc tape rmt0 Available 02-08-00 SAS 4mm Tape Drive#lsattr -El rmt0 #lscfg -vpl rmt0 rmt0 U78A0.001.DNWK9W6-P2-D1 SAS 4mm Tape Drive (80000 MB) Hardware Location Code......U78A0.001.DNWK9W6-P2-D1 当主机接了磁带库，tape driver数量未知的情况下，可以采用以下脚本一次性收集所有tape driver信息：

1.      echo "#lsdev -Cc tape"

2.      lsdev -Cc tape

3.      for i in `lsdev -Cc tape|awk '{print $1}'`

4.      do

5.      echo "nInformation about "$i "n#lsattr -El" $i

6.      lsattr -El $i

7.      echo "n#lscfg -vl " $i

8.      lscfg -vl $i

9.      done

复制代码六、查看VG、PV、LV信息 查看系统中所有VG#lsvg rootvg vgora 查看当前active的VG#lsvg -o vgora rootvg#lsvg -p rootvg rootvg: PV_NAME PV STATE TOTAL PPs FREE PPs FREE DISTRIBUTION hdisk0 active 558 429 111..68..27..111..112 hdisk1 active 558 437 111..76..27..111..112#lsvg -l rootvg 查看所有PV#lspv hdisk0 00cb01e637be5983 rootvg active hdisk1 00cb01e6dd9045e6 rootvg active#lspv -l hdisk0 当VG数量未知时，可用以下脚本一次性收集所有VG、LV信息（可结合上文disk信息） echo "#lsvg " lsvg echo "#lsvg -o" lsvg -o for i in `lsvg`; do echo "nInformation about VG "$i "n#lsvg " $i lsvg $i echo "n#lsvg -l " $i lsvg -l $i echo "n#lsvg -p " $i lsvg -p $i echo "n#lsvg -M " $i lsvg -M ${i} done