锐捷基本命令手册 | 您所在的位置:网站首页 › 汛组词拼音造句 › 锐捷基本命令手册 |
Enable 进入特权模式 #Exit 返回上一级操作模式 #End 返回到特权模式 #write memory 或copy running-config startup-config 保存配置文件 #del flash:config.text 删除配置文件(交换机及1700系列路由器) #erase startup-config 删除配置文件(2500系列路由器) #del flash:vlan.dat 删除Vlan配置信息(交换机) #Configure terminal 进入全局配置模式 (config)# hostname switchA配置设备名称为switchA (config)#banner motd & 配置每日提示信息&为终止符 (config)#enable secret level 1 0 star 配置远程登陆密码为star (config)#enable secret level 15 0 star 配置特权密码为star Level 1为普通用户级别,可选为1~15,15为最高权限级别;0表示密码不加密 (config)#enable services web-server 开启交换机WEB管理功能 Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等查看信息 #show running-config 查看当前生效的配置信息 #show interface fastethernet 0/3 查看F0/3端口信息 #show interface serial 1/2 查看S1/2端口信息 #show interface 查看所有端口信息 #show ip interface brief 以简洁方式汇总查看所有端口信息 #show ip interface 查看所有端口信息 #show version 查看版本信息 #show mac-address-table 查看交换机当前MAC地址表信息 #show running-config 查看当前生效的配置信息 #show vlan 查看所有VLAN信息 #show vlan id 10 查看某一VLAN (如VLAN10)的信息 #show interface fastethernet 0/1 switchport 查看某一端口模式(如F 0/1) #show aggregateport 1 summary 查看聚合端口AG1的信息 #show spanning-tree 查看生成树配置信息 #show spanning-tree interface fastethernet 0/1 查看该端口的生成树状态 #show port-security 查看交换机的端口安全配置信息 #show port-security address 查看地址安全绑定配置信息 #show ip access-lists listname 查看名为listname的列表的配置信息 #show access-lists 端口的基本配置 (config)#Interface fastethernet 0/3 进入F0/3的端口配置模式 (config)#interface range fa 0/1-2,0/5,0/7-9 进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式 (config-if)#speed 10 配置端口速率为10M,可选10,100,auto (config-if)#duplex full 配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应) (config-if)#no shutdown 开启该端口 (config-if)#switchport access vlan 10 将该端口划入VLAN10中,用于VLAN (config-if)#switchport mode trunk 将该端口设为trunk模式,用于Tag vlan 可选模式为access , trunk (config-if)#port-group 1 将该端口划入聚合端口AG1中,用于聚合端口 聚合端口的创建 (config)# interface aggregateport 1 创建聚合接口AG1 (config-if)# switchport mode trunk 配置并保证AG1为trunk 模式 (config)#int f0/23-24 (config-if-range)#port-group 1 将端口(端口组)划入聚合端口AG1中 生成树 (config)#spanning-tree 开启生成树协议 (config)#spanning-tree mode stp 指定生成树类型为stp 可选模式stp , rstp , mstp (config)#spanning-tree priority 4096 设置交换机的优先级为4096 , 优先级值小为高。优先级可选值为0,4096,8192,……,为4096的倍数。交换机默认值为32768 VLAN的基本配置 (config)#vlan 10 创建VLAN10 (config-vlan)#name vlanname 命名VLAN为vlanname (config-if)#switchport access vlan 10 将该端口划入VLAN10中 某端口的接口配置模式下进行 (config)#interface vlan 10 进入VLAN 10的虚拟端口配置模式 (config-if)# ip address 192.168.1.1 255.255.255.0 为VLAN10的虚拟端口配置IP及掩码,二层交换机只能配置一个IP,此IP是作为管理IP使用,例如,使用Telnet的方式登录的IP 地址 (config-if)# no shutdown 启用该端口 端口安全 (config)# interface fastethernet 0/1 进入一个端口 (config-if)# switchport port-security 开启该端口的安全功能 1.配置最大连接数限制 (config-if)# switchport port-secruity maxmum 1 配置端口的最大连接数为1,最大连接数为128 (config-if)# switchport port-secruity violation shutdown 配置安全违例的处理方式为shutdown,可选为protect (当安全地址数满后,将未知名地址丢弃)、restrict(当违例时,发送一个Trap通知)、shutdown(当违例时将端口关闭,并发送Trap通知,可在全局模式下用errdisable recovery来恢复) 2.IP和MAC地址绑定 (config-if)#switchport port-security mac-address xxxx.xxxx.xxxx ip-address 172.16.1.1 接口配置模式下配置MAC地址xxxx.xxxx.xxxx和IP172.16.1.1进行绑定(MAC地址注意用小写) 三层路由功能(针对三层交换机) (config)# ip routing 开启三层交换机的路由功能 (config)# interface fastethernet 0/1 (config-if)# no switchport 开启端口的三层路由功能(这样就可以为某一端口配置IP) (config-if)# ip address 192.168.1.1 255.255.255.0 (config-if)# no shutdown 三层交换机路由协议 (config)# ip route 172.16.1.0 255.255.255.0 172.16.2.1 配置静态路由 注:172.16.1.0 255.255.255.0 为目标网络的网络号及子网掩码 172.16.2.1 为下一跳的地址,也可用接口表示,如ip route 172.16.1.0 255.255.255.0 serial 1/2(172.16.2.0所接的端口) (config)# router rip 开启RIP协议进程 (config-router)# network 172.16.1.0 申明本设备的直连网段信息 (config-router)# version 2 开启RIP V2,可选为version 1(RIPV1)、version 2(RIPV2) (config-router)# no auto-summary 关闭路由信息的自动汇总功能(只有在RIPV2支持) (config)# router ospf 开启OSPF路由协议进程(针对1762,无需使用进程ID) (config)# router ospf 1 开启OSPF路由协议进程(针对2501,需要加OSPF进程ID) (config-router)# network 192.168.1.0 0.0.0.255 area 0 申明直连网段信息,并分配区域号(area0为骨干区域) IP ACL: 交换机采用命名的访问控制列表;分标准(stand)和扩展(extended)两种 1.标准ACL (config)#ip access-list stand listname 定义命名标准列表,命名为listname,stand为标准列表 (config-std-nacl)#deny 192.168.30.0 0.0.0.255 拒绝来自192.168.30.0网段的IP流量通过注:deny:拒绝通过;可选:deny(拒绝通过)、permit(允许通过) 192.168.30.0 0.0.0.255:源地址及源地址通配符;可使用any表示任何IP (config-std-nacl)#permit any (config-std-nacl)#end 返回 2.扩展ACL (config)#ip access-list extended listname 定义命名扩展列表,命名为listname,extended为扩展 (config-ext-nacl)#deny tcp 192.168.30.0 0.0.0.255 192.168.10.0 0.0.0.255 eq www 拒绝源地址为192.168.30.0网段的IP访问目的地址为192.168.10.0网段的WWW服务注:deny:拒绝通过,可选:deny(拒绝通过)、permit(允许通过) tcp: 协议名称,协议可以是udp, ip,eigrp, gre, icmp, igmp, igrp等等。 192.168.10.0 0.0.0.255:源地址及源地址通配符 192.168.30.0 0.0.0.255:目的地址及目的地址通配符 eq:操作符(lt-小于,eq-等于,gt-大于,neg-不等于,range-包含) www:端口号,可使用名称或具体编号 可以使用的协议名称(或编号)和端口名称(或编号)请打?查询。 (config-ext-nacl)#permit ip any any 允许其它通过 (config-ext-nacl)#end 返回 (config)#interface vlan 10 进入端口配置模式 (config-if)# ip access-group listname in 访问控制列表在端口下in方向应用;可选:in(入栈)、out(出栈) (config-if)#end 返回 注:配置ACL时,若只想对其中部分IP进行限制访问时,必须配置允许其流量通过,否则设备只会对限制IP进行处理,不会对非限制IP进行允许通过处理。 在锐捷交换机上配置vrrp、arp和mstp 交换机 密码 1234(config)#enable secret level 1 0 100 1234(config)#enable secret level 15 0 100 远程登入密码 1234(config)#line vty 0 4 1234(config-line)#password 100 1234(config-line)#end 交换机管理IP 1234(config)#interface vlan 1 1234(config-if)#ip address 192.168.1.10 255.255.255.0 1234(config-if)#no shutdown 修改交换机老化时间 1234(config)#mac-address-table aging-time 20 1234(config)#end 添删vlan 1234(config)#vlan 888 1234(config-vlan)#name a888 1234(config)#no vlan 888 添加access口 1234(config)#interface gigabitEthernet 0/10 1234(config-if)#switchport mode access 1234(config-if)#switchport access vlan 10 切换assess trunk 1234(config-if)#switchport mode access 1234(config-if)#switchport mode trunk 指定特定一个native vlan 1234(config-if)#switchport trunk native vlan 10 配置trunk口的许可vlan列表 1234(config-if)#switchport trunk allowed vlan ? add Add VLANs to the current list all All VLANs except All VLANs except the following remove Remove VLANs from the current list 速成树协议 1234(config)#spanning-tree 1234(config)#spanning-tree mode rstp/stp 配置网关: switch(config)#ip default-gateway 192.168.1.254 交换机基本配置-常见查看命令 查看CPU利用率 show cpu 查看交换机时钟 show clock 查看交换机日志 show logging 查看交换机动态学习到的MAC地址表 show mac-address-table dynamic 查看当前交换机运行的配置文件 show running-config 查看交换机硬件、软件信息 show version 查看交换机的arp表 show arp 显示接口详细信息的命令 show interfaces gigabitEthernet 4/1 counters 接口配置 Switch(config)#interface gigabitethernet 0/1 把接口工作模式改为光口。 Switch(config-if)#medium-type fiber 把接口工作模式改为电口。 Switch(config-if)#medium-type copper 速度/双工配置 进入接口配置模式。 Switch(config)#interface interface-id 设置接口的速率参数,或者设置为auto。 Switch(config-if)#speed {10 | 100 | 1000 | auto } 设置接口的双工模式。 Switch(config-if)#duplex {auto | full | half} 例子 Switch(config)#interface gigabitethernet 0/1 Switch(config-if)#speed 1000 Switch(config-if)#duplex full 光口不能修改速度和双工配置,只能auto。 在故障处理的时候,如果遇到规律性的时断时续或掉包,在排除其他原因后,可以考虑是否和对端设备的速率和双工模式不匹配,尤其是两端设备为不同厂商的时候。 VLAN 建立VLAN 100 Switch (config)#vlan 100 该VLAN名称为ruijie Switch (config)#name ruijie 将交换机接口划入VLAN 中: range表示选取了系列端口1-48,这个对多个端口进行相同配置时非常有用。 Switch (config)#interface range f 0/1-48 将接口划到VLAN 100中。 Switch (config-if-range)#switchport access vlan 100 将接口划回到默认VLAN 1中,即端口初始配置。 Switch (config-if-range)#no switchport access vlan Switch(config)#interface fastEthernet 0/1 该端口工作在access模式下 Switch(config-if)#switchport mode access 该端口工作在trunk模式下 Switch(config-if)#switchport mode trunk Switch(config)#interface fastEthernet 0/2 设定VLAN要修剪的VLAN。 Switch(config-if)#switchport trunk allowed vlan remove 2-9,11-19,21-4094 取消端口下的VLAN修剪。 Switch(config-if)#no switchport trunk allowed vlan 生成树 开启生成树协议。 Switch(config)#spanning-tree 禁止生成树协议。 Switch(config)#no spanning-tree 配置生成树优先级: 配置设备优先级为4096。 Switch(config)#spanning-tree priority 4096 数值越低,优先级别越高。 端口镜像 配置G0/2为镜像端口。 Switch (config)# monitor session 1 destination interface G 0/2 配置G0/1为被镜像端口,且出入双向数据均被镜像。 Switch (config)# monitor session 1 source interface G 0/1 both 去掉镜像1。 Switch (config)# no monitor session 1 端口聚合 Switch(config)#interface fastEthernet 0/1 把端口f0/1加入到聚合组1中。 Switch (config-if)#port-group 1 把端口f0/1从聚合组1中去掉 Switch (config-if)#no port-group 1 建立ACL: 建立ACL访问控制列表名为ruijie,extend表示建立的是扩展访 Switch(config)# Ip access-list exten ruijie 问控制列表。 添加ACL的规则: 禁止PING IP地址为192.168.1.1的设备。 Switch (config-ext-nacl)#deny icmp any 192.168.1.1 255.255.255.0 禁止端口号为135的应用。 Switch (config-ext-nacl)# deny tcp any any eq 135 禁止协议为www的应用。 Switch (config-ext-nacl)#deny udp any any eq www 允许所有行为。 Switch(config-ext-nacl)# permit ip any any 将ACL应用到具体的接口上: Switch (config)#interface range f 0/1 把名为ruijie的ACL应用到端口f 0/1上。 Switch (config-if)#ip access-group ruijie in 从接口去除ACL。 Switch (config-if)#no ip access-group ruijie in 删除ACL: 删除名为ruijie的ACL。 Switch(config)#no Ip access-list exten ruijie 增加ACE项后,是增加到ACL最后,不可以中间插入,如果要调整ACE的顺序,必须整个删除ACL后再重新配置。 端口安全 Switch (config)#interface range f 0/1 开启端口安全。 Switch(config-if)# switchport port-security 关闭端口安全。 Switch(config-if)# no switchport port-security 设置端口能包含的最大安全地址数为8。 Switch(config-if)# switchport port-security maximum 8 在接口fastethernet0/1配置一个安全地址00d0.f800.073c,并为其绑定一个IP地址192.168.1.1 Switch(config-if)# switchport port-security mac-address 00d0.f800.073c ip-address 192.168.1.1 删除接口上配置的安全地址。 Switch(config-if)#no switchport port-security mac-address 00d0.f800.073c ip-address 192.168.1.1 防ARP攻击 IP和MAC地址的绑定 Switch(config)#arp ip-address hardware-address [type] interface-id Switch(config)#arp 192.168.12.111 00d0.f800.073c arpa g 0/1 绑定网关 进入指定端口进行配置。 Switch(config)#Interface interface-id 配置防止ip-address的ARP欺骗。 Switch(config-if)#Anti-ARP-Spoofing ip ip-address 防STP攻击 进入端口Fa0/1。 Switch(config)# inter fastEthernet 0/1 打开该端口的的BPDU guard功能。 Switch(config-if)# spanning-tree bpduguard enable 关闭该端口的的BPDU guard功能。 Switch(config-if)# spanning-tree bpduguard diaable 端口关闭后只能shutdown然后再no shutdown 或者重新启动交换机才能恢复! 防DOS/DDOS攻击 进入端口Fa0/1。 Switch(config)# inter fastEthernet 0/1 预防伪造源IP的DOS攻击的入口过滤功能。 Switch(config-if)#ip deny spoofing-source 关闭入口过滤功能只能在三层接口上配置。 Switch(config-if)#no ip deny spoofing-source 和ACL不能同时存在。 端口关闭后只能shutdown然后再no shutdown 或者重新启动交换机才能恢复! 防IP扫描攻击配置: 打开系统保护。 Switch(config)#system-guard enable 关闭系统保护功能。 Switch(config)#no system-guard DHCP配置 打开DHCP Relay Agent: Switch(config)#service dhcp 配置DHCP Server的IP地址: Switch(config)#ip helper-address address VRRP配置 Switch(config)#Interface interface-id Switch(config-if)#Standby [group-number] ip ip-address 设置虚拟机的优先级。 standby [group-number] priority priority 三层交换机配置 SVI: 把VLAN 10配置成SVI。 switch (config)#interface vlan 10 给该SVI接口配置一个IP地址 switch (config-if)#ip address 192.168.1.1 255.255.255.0 Routed Port: switch (config)#interface fa 0/1 把f 0/1变成路由口。 switch (config-if)#no switch 路由配置: 添加一条路由。 switch (config)#ip route 目的地址掩码下一跳 switch (config)#ip route 210.10.10.0 255.255.255.0 218.8.8.8 配置多生成树协议: switch(config)#spanning-tree //开启生成树协议 switch(config)#spanning-tree mst configuration //建立多生成树协议 switch(config-mst)#name ruijie //命名为ruijie switch(config-mst)#revision 1 //设定校订本为1 switch(config-mst)#instance 0 vlan 10,20 //建立实例0 switch(config-mst)#instance 1 vlan 30,40 //建立实例1 switch(config)#spanning-tree mst 0 priority 4096 //设置优先级为4096 switch(config)#spanning-tree mst 1 priority 8192 //设置优先级为8192 switch(config)#interface vlan 10 switch(config-if)#vrrp 1 ip 192.168.10.1 //此为vlan 10的IP地址 switch(config)#interface vlan 20 switch(config-if)#vrrp 1 ip 192.168.20.1 //此为vlan 20的IP地址 switch(config)#interface vlan 30 switch(config-if)#vrrp 2 ip 192.168.30.1 //此为vlan 30的IP地址(另一三层交换机) switch(config)#interface vlan 40 switch(config-if)#vrrp 2 ip 192.168.40.1 //此为vlan 40的IP地址(另一三层交换机) 此配置需在两个三层交换机和二层交换机上进行配置!在二层交换机上不用配置VRRP! 冗余链路 在骨干网设备连接中,单一链路的连接很容易实现,但一个简单的故障就会造成网络的中断.因此在实际网络组建的过程中,为了保持网络的稳定性,在多台交换机组成的网络环境中,通常都使用一些备份连接,以提高网络的健壮性、稳定性. 这里的备份连接也称为备份链路或者冗余链路.备份链路之间的交换机经常互相连接,形成一个环路,通过环路可以在一定程度上实现冗余 链路的冗余备份能为网络带来健壮性、稳定性和可靠性等好处,但是备份链路也会使网络存在环路,环路问题是备份链路所面临的最为严重的问题,交换机之间的环路将导致网络新问题的发生: 广播风暴 多帧复制 地址表的不稳定 解决方法: 生成树协议避免环路 每个LAN都会选择一台设备为指定交换机,通过该设备的端口连接到根,该端口为指定端口(Designated port ) 将交换网络中所有设备的根端口(RP)和指定端口(DP)设为转发状态(Forwarding),将其他端口设为阻塞状态(Blocking) 生成树经过一段时间(默认值是50秒左右)稳定之后,所有端口要么进入转发状态,要么进入阻塞状态。 IEEE 802.1w—快速生成树协议 快速生成树协议概述 快速生成树协议RSTP(Rapid Spannning Tree Protocol) IEEE 802.1w RSTP协议在STP协议基础上做了改进,使得收敛速度快得多(最快1秒以内) 生成树协议的配置 开启生成树协议 Switch(config)#Spanning-tree 关闭生成树协议 Switch(config)#no Spanning-tree 配置生成树协议的类型 Switch(config)#Spanning-tree mode stp/rstp 锐捷全系列交换机默认使用MSTP协议 配置交换机优先级 Switch(config)#spanning-tree priority (“0”或“4096”的倍数、共16个、缺省32768) 恢复到缺省值 Switch(config)# no spanning-tree priority 配置交换机端口的优先级 Switch(config)#interface interface-type interface-number Switch(config-if)#spanning-tree port-priority number 显示生成树状态 Switch#show spanning-tree 显示端口生成树协议的状态 Switch#show spanning-tree interface fastethernet 生成树协议概述 生成树协议(spanning-tree protocol)由IEEE 802.1d标准定义 生成树协议的作用是为了提供冗余链路,解决网络环路问题 生成树协议通过SPA(生成树算法)生成一个没有环路的网络,当主要链路出现故障时,能够自动切换到备份链路,保证网络的正常通信 配置模式: 全局配置模式switch(config)# 配置交换机的整体参数 接口配置模式switch(config-if)# 配置交换机的接口参数 进入全局配置模式 Switch#c onfigure terminal Switch(config)#exit Switch# 进入接口配置模式 Switch(config)#interface fastethernet 0/1 Switch(config-if)#exit Switch(config)# 从子模式下直接返回特权模式 Switch(config-if)#end Switch# 命令行其他功能 获得帮助 switch#? switch#show ? 命令简写 全写:switch# configure terminal 简写:Switch# config 使用历史命令 Switch# (向上键) Switch# (向下键) 配置交换机Telnet功能 配置远程登陆密码 Switch(config)#enable secret level 1 0 ruijie 配置进入特权模式密码 Switch (config)#enable secret level 15 0 ruijie 为交换机配置管理IP Switch (config)#interface vlan 1 Switch (config-if)#no shutdown Switch (config-if)#ip address 192.168.1.1 255.255.255.0 Switch (config-if)#end 配置文件的管理 保存配置 将当前运行的参数保存到flash 中用于系统初始化时初始化参数Switch#copy running-config startup-config Switch#write memory Switch#write 删除配置 永久性的删除flash 中不需要的文件 使用命令delete flash:config.text 删除当前的配置:在配置命令前加no 例:switch(config-if)# no ip address 查看配置文件内容 Switch#show configure 查看保存在FLASH里的配置信息Switch#show running-config 查看RAM里当前生效的配置配置Port VLAN 创建VLAN10,将它命名为test的例子 Switch# configure terminal Switch(config)# vlan 10 Switch(config-vlan)# name test Switch(config-vlan)# end 把接口0/10加入VLAN10 Switch# configure terminal Switch(config)# interface fastethernet 0/10 Switch(config-if)# switchport mode access Switch(config-if)# switchport access vlan 10 Switch(config-if)# end 将一组接口加入某一个VLAN Switch(config)#interface range fastethernet 0/1-8,0/15,0/20 Switch(config-if-range)# switchport access vlan 20 注:连续接口0/1-8,不连续接口用逗号隔开,但一定要写明模块编号 配置Tag VLAN-Trunk 把Fa0/1配成Trunk口 Switch# configure terminal Switch(config)# interface fastethernet0/1 Switch(config-if)# switchport mode trunk 把端口Fa0/20 配置为Trunk端口,但是不包含VLAN 2: Switch(config)# interface fastethernet 0/20 Switch(config-if)# switchport trunk allowed vlan remove 2 Switch(config-if)# end Native VLAN 配置命令: Switch(config-if)# switchport trunk native vlan 20 Switch(config-if)# end 注意: 每个Trunk口的缺省native VLAN是VLAN 1 在配置Trunk链路时,请确保连接链路两端的Trunk口属于相同的native VLAN 保存/清除VLAN信息 将VLAN信息保存到flash中 Switch#write memory 从flash中只清除VLAN信息 Switch#delete flash:vlan.dat 从RAM中删除VLAN Switch(config)#no vlan VLAN-id 生成树协议的配置 开启生成树协议 Switch(config)#Spanning-tree 关闭生成树协议 Switch(config)#no Spanning-tree 配置生成树协议的类型 Switch(config)#Spanning-tree mode stp/rstp 锐捷全系列交换机默认使用MSTP协议 配置交换机优先级 Switch(config)#spanning-tree priority (“0”或“4096”的倍数、共16个、缺省32768) 恢复到缺省值 Switch(config)# no spanning-tree priority 配置交换机端口的优先级 Switch(config)#interface interface-type interface-number Switch(config-if)#spanning-tree port-priority number 配置STP、RSTP Spanning Tree 的缺省配置: 关闭STP STP Priority 是32768 STP port Priority 是128 STP port cost 根据端口速率自动判断 Hello Time 2秒 Forward-delay Time 15秒 Max-age Time 20秒 可通过spanning-tree reset 命令让spanning tree参数恢复到缺省配置查看生成树协议配置 显示生成树状态 Switch#show spanning-tree 显示端口生成树协议的状态 Switch#show spanning-tree interface fastethernet 配置aggregate port 将该接口加入一个AP Switch#c onfigure terminal Switch(config) # interface interface-type interface-id Switch(config-if-range)#port-group port-group-number 如果这个AP不存在,可自动创建AG端口 查看聚合端口的汇总信息 Switch#show aggregateport summary 查看聚合端口的流量平衡方式 Switch#show aggregateport load-balance 路由器上配置telnet 第一步: 配置端口地址 RouterA# configure terminal !进入全局配置模式 RouterA(config)# interface fastethernet 1/0 !进入路由器接口配置模式 RouterA(config-if)# ip address 192.168.0.1 255.255.255.0 !配置路由器管理接口IP地址 RouterA(config-if)# no shutdown !开启路由器f 1/0接口 第二步:配置远程登录密码 RouterA(config)# line vty 0 4 !进入路由器线路配置模式 RouterA(config-line)# login !配置远程登录 RouterA(config-line)# password star !设置路由器远程登录密码为“star”RouterA(config-line)#end 第三步:配置路由器特权模式密码 RouterA(config)# enable secret star !设置路由器特权模式密码为“star”或者 RouterA(config)# enable password star 查看配置文件 show version !查看版本及引导信息 show running-config !查看运行配置 show startup-config !查看用户保存在NVRAM中的配置文件 保存配置文件 Router#copy running-config startup-config Router#write memory Router#write 删除配置文件 Router#delete flash:config.text !删除初始配置文件 查看路由信息 router#show ip route Codes: C - connected,S static,R RIP,O- OSPF IA - OSPF inter area,E1-OSPF external type 1 E2 - OSPF external type 2,* - candidate default Gateway of last resort is 10.5.5.5 to network 0.0.0.0 172.16.0.0/24 is subnetted, 1 subnets C 172.16.11.0 is directly connected, serial1/2 O E2 172.22.0.0/16 [110/20] via 10.3.3.3, 01:03:01, Serial1/2 S* 0.0.0.0/0 [1/0] via 10.5.5.5 静态路由配置命令 配置静态路由用命令ip route router(config)#ip route [网络编号] [子网掩码] [转发路由器的IP地址/本地接口] 例:ip route 192.168.10.0 255.255.255.0 serial 1/2 例:ip route 192.168.10.0 255.255.255.0 172.16.2.1 静态路由描述转发路径的方式有两种 指向本地接口(即从本地某接口发出) 指向下一跳路由器直连接口的IP地址(即将数据包交给X.X.X.X)配置默认路由: router(config)#ip route 0.0.0.0 0.0.0.0 [转发路由器的IP地址/本地接口] RIP路由协议的版本 RIPv1 有类路由协议,不支持VLSM 以广播的形式发送更新报文 不支持认证 RIPv2 无类路由协议,支持VLSM 以组播的形式发送更新报文 支持明文和MD5的认证 配置RIP协议 配置步骤 1、开启RIP路由协议进程 Router(config)#router rip 2、申请本路由器参与RIP协议的直连网段信息 Router(config-router)#network 192.168.1.0 3、指定RIP协议的版本2(默认是version1) Router(config-router)#version 2 4、在RIPv2版本中关闭自动汇总 Router(config-router)#no auto-summary 查看RIP配置信息 验证RIP的配置 Router#show ip protocols 显示路由表的信息 Router#show ip route 清除IP路由表的信息 Router#clear ip route 在控制台显示RIP的工作状态 Router#debug ip rip OSPF协议 OSPF配置如下: 1、创建loopback接口,定义ROUTE ID routerA(config)#interface loopback 10 routerA(config)#ip address 192.168.100.1 255.255.255.0 2、开启OSPF进程 routerA(config)#router ospf 10 10代表进程编号,只具有本地意义 3、申请直连网段 routerA(config-router)#network 10.1.1.0 0.0.0.255 area 0 注意反掩码和区域号 查看OSPF配置信息 验证OSPF的配置 Router#show ip ospf 显示路由表的信息 Router#show ip route 清除IP路由表的信息 Router#clear ip route 在控制台显示OSPF的工作状态 Router#debug ip ospf 三层交换的路由功能 三层交换机默认开启路由功能 Switch(config)#ip routing (开启三层交换机路由功能) 三层交换机配置路由接口的两种方法 开启三层交换机物理接口的路由功能 Switch(config)#interface fastethernet 0/5 Switch(config-if)#no switchport Switch(config-if)#ip address 192.168.1.1 255.255.255.0 Switch(config-if)#no shutdown 关闭物理接口路由功能 Switch(config-if)# switchport 采用SVI方式(switch virtual interface) Switch(config)#interface vlan 10 Switch(config-if)#ip address 192.168.1.1.255 255.255.0 Switch(config-if)#no shutdown 三层交换机和路由器相连的网络 方法一(SVI): Switch(config)#interface f0/10 Switch(config-if)#switchport access vlan 10 Switch(config-if)#exit Switch(config)#interface vlan 10 switch(config-if)#ip address 192.168.10.1 255.255.255.0 Switch(config-if)#no shutdown 方法二(路由接口): Switch(config)#interface f0/10 Switch(config-if)#no switchport Switch(config-if)#ip address 192.168.10.1 255.255.255.0 Switch(config-if)#no shutdown 三层交换机路由协议的配置 静态路由 Switch(config)#ip route x.x.x.x x.x.x.x [x.x.x.x/interface] RIP Switch(config)#router rip Switch(config-router)#network X.X.X.X Switch(config-router)#version 2 注:三层交换机不支持no auto-summary OSPF Switch(config)#router ospf Switch(config)#network X.X.X.X X.X.X.X area x 查看三层交换机路由配置 查看路由接口信息 Switch#show ip interface |
CopyRight 2018-2019 实验室设备网 版权所有 |