jetson nano设置静态ip和发出热点 |
您所在的位置：网站首页 › 以太网连接手机热点 › jetson nano设置静态ip和发出热点 |
jetson nano设置静态ip和发出热点
|
查看ip地址，网关，掩码
wheeltec@wheeltec:~$ ip a
1: lo: mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: dummy0: mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether b6:f0:d6:29:0e:d9 brd ff:ff:ff:ff:ff:ff
3: eth0: mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
link/ether 00:e0:4c:68:01:fd brd ff:ff:ff:ff:ff:ff
4: l4tbr0: mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 5e:ce:9b:44:0b:e5 brd ff:ff:ff:ff:ff:ff
5: rndis0: mtu 1500 qdisc pfifo_fast master l4tbr0 state DOWN group default qlen 1000
link/ether 5e:ce:9b:44:0b:e5 brd ff:ff:ff:ff:ff:ff
6: usb0: mtu 1500 qdisc pfifo_fast master l4tbr0 state DOWN group default qlen 1000
link/ether 5e:ce:9b:44:0b:e7 brd ff:ff:ff:ff:ff:ff
7: wlan0: mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 34:13:e8:5e:70:31 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.109/24 brd 192.168.1.255 scope global dynamic noprefixroute wlan0
valid_lft 7104sec preferred_lft 7104sec
inet6 fe80::1290:cc31:d44e:f537/64 scope link noprefixroute
valid_lft forever preferred_lft forever
inet 192.168.1.109/24 brd 192.168.1.255 scope global dynamic noprefixroute 表示ip地址是192.168.1.109，dynamic表示是动态ip wheeltec@wheeltec:~$ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 600 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.1.0 0.0.0.0 255.255.255.0 U 600 0 0 wlan0IP地址 192.168.1.109 子网掩码netmask 255.255.255.0 网关Gateway192.168.1.1 这是我的网络参数，大家的会有点不同 设置静态ip 点击nano桌面上角的网络图标选择“Edit Connections”双击自己连接的WIFI，点击IPV4 Settings，选择Add填入ip地址，子网掩码和网关，保存
重启，设置的静态ip才会生效 wheeltec@wheeltec:~$ sudo reboot 验证 wheeltec@wheeltec:~$ ip a 1: lo: mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: dummy0: mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether 52:d1:a4:70:1a:28 brd ff:ff:ff:ff:ff:ff 3: eth0: mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000 link/ether 00:e0:4c:68:01:fd brd ff:ff:ff:ff:ff:ff 4: l4tbr0: mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether 5e:ce:9b:44:0b:e5 brd ff:ff:ff:ff:ff:ff 5: rndis0: mtu 1500 qdisc pfifo_fast master l4tbr0 state DOWN group default qlen 1000 link/ether 5e:ce:9b:44:0b:e5 brd ff:ff:ff:ff:ff:ff 6: usb0: mtu 1500 qdisc pfifo_fast master l4tbr0 state DOWN group default qlen 1000 link/ether 5e:ce:9b:44:0b:e7 brd ff:ff:ff:ff:ff:ff 7: wlan0: mtu 1500 qdisc mq state UP group default qlen 1000 link/ether 34:13:e8:5e:70:31 brd ff:ff:ff:ff:ff:ff inet 192.168.1.109/24 brd 192.168.1.255 scope global noprefixroute wlan0 valid_lft forever preferred_lft forever inet6 fe80::61c8:3ecc:e895:4556/64 scope link noprefixroute valid_lft forever preferred_lft foreverinet 192.168.1.109/24 brd 192.168.1.255 scope global noprefixroute wlan0 valid_lft forever preferred_lft forever ip地址为192.168.1.109,没有dynamic，是静态ip 发出热点1. 点击nano桌面上角的网络图标 2. 选择“Edit Connections” 3. 点击“+”，选择WIFI
6.设置静态ip，保存热点就设置完成 **8.重启nano sudo reboot不重启，连不上wifi。在电脑上，能看见“jetson nano”的wifi，连接以后不能上网，就是用来和虚拟机通信使用的。** |
4. 修改Connection name（任意，我的是test）.修改SSID，SSID就是热点的名称（我的是jetson nano）mode选择“Hotspot” 
5.设置热点密码 
7.发出热点，点击桌面右上角网络图标，选择“Connect to Hidden WiFi Network”，选择自己设置的热点，选择“connect”，就可以发出热点 
【本文地址】
公司简介
联系我们
今日新闻 |
点击排行 |
|
推荐新闻 |
图片新闻 |
|
专题文章 |