[huawei-wlan-view]radio-2g-profile name r2 //进入2G射频模板视图 [huawei-wlan-view]radio-5g-profile name r5 //进入5G射频模板视图 [huawei-wlan-radio-5g-prof-r5]interference detect-enable //使能干扰检测功能 [huawei-wlan-radio-5g-prof-r5]interference co-channel threshold 50 //配置同频干扰的告警门限值,缺省为50% [huawei-wlan-radio-5g-prof-r5]interference station threshold 32 //配置STA干扰的告警门限值,缺省为32 [huawei]display radio-5g-profile name r5 //看5G射频模板下的干扰检测的配置信息 [huawei]display radio-2g-profile name r2 //查看2G射频模板下的干扰检测的配置信息 [huawei-wlan-view]rrm-profile name r1 //进入RRM模板视图 [huawei-wlan-view]radio-5g-profile name r5 //进入5G射频模板视图 [huawei-wlan-radio-5g-prof-r5]rrm-profile r1 //将RRM模板绑定到5G射频模板 [huawei-wlan-view]calibrate enable auto //配置射频调优的模式, 缺省射频调优的模式为auto模式，调优的时间间隔为1440分钟，起始时间为00:00:00 [huawei-wlan-view]calibrate enable manual [huawei-wlan-view]calibrate policy rogue-ap //创建射频调优策略为入侵模式 [huawei-wlan-view]calibrate policy load //创建射频调优策略为负载 [huawei-wlan-view]calibrate policy non-wifi //创建射频调优策略为非Wi-Fi [huawei-wlan-view]regulatory-domain-profile name r1 //进入域管理模板视图 [huawei-wlan-regulate-domain-r1]dca-channel 5g bandwidth 20mhz //配置调优带宽,缺省全局调优带宽是20MHz,此命令仅针对5G频段有效 [huawei-wlan-regulate-domain-r1]dca-channel 5g channel-set 36 40 44 //配置调优信道集合,缺省2G射频下为1、6、11信道，5G射频为对应国家码下的所有信道。特别地，若对应国家码为中国，则缺省调优信道不包含36～64信道。用户在配置调优信道时，可根据屏幕提示指定信道 [huawei-wlan-regulate-domain-r1]dca-channel 2.4g channel-set 1 2 3 [huawei-wlan-view]air-scan-profile name a1 //创建空口扫描模板并进入空口扫描模板视图 [huawei-wlan-air-scan-prof-a1]scan-channel-set country-channel //配置空口扫描信道集合,缺省空口扫描信道集合为RU对应国家码支持的所有信道；如果射频工作模式为监控模式，则扫描AP对应国家码支持的所有信道 [huawei-wlan-air-scan-prof-a1]scan-channel-set dca-channel [huawei-wlan-air-scan-prof-a1]scan-channel-set work-channel [huawei-wlan-air-scan-prof-a1]scan-interval 60000 //配置空口扫描间隔时间,缺省为60000毫秒 [huawei-wlan-air-scan-prof-a1]scan-period 60 //配置空口扫描持续时间,缺省为60毫秒 [huawei-wlan-view]radio-5g-profile name r5 //进入5G射频模板视图 [huawei-wlan-radio-5g-prof-r5]air-scan-profile a1 //将空口扫描模板绑定到5G射频模板 [huawei-wlan-view]display wlan calibrate channel-set ap-group all //查看生效的调优信道和调优带宽 [huawei-wlan-view]display regulatory-domain-profile name r1 //查看配置的调优信道集合和调优带宽 [huawei-wlan-view]display rrm-profile name r1 //查看AP信道和发送功率是否使能自动选择功能 [huawei-wlan-view]display air-scan-profile name a1 //查看空口扫描模板的配置信息 [huawei-wlan-view]display radio-5g-profile name r5 //查看5G射频模板下的引用的RRM模板和空口扫描模板 [huawei-wlan-view]calibrate manual startup //立即触发调优功能 [huawei-wlan-view]sta-load-balance static-group name s1 //创建静态负载均衡组并进入静态负载均衡组视图 [huawei-wlan-sta-lb-static-s1]member ap-id 0 //向负载均衡组中添加AP射频 [huawei-wlan-sta-lb-static-s1]member ap-name ap1 [huawei-wlan-sta-lb-static-s1]start-threshold 10 //配置静态负载均衡组的负载均衡起始门限,缺省是10 [huawei-wlan-sta-lb-static-s1]gap-threshold 20 //配置静态负载均衡组的负载差值门限,缺省为20% [huawei-wlan-sta-lb-static-s1]deny-threshold 3 //配置静态负载均衡组的拒绝关联最大次数,缺省为3 [huawei-wlan-sta-lb-static-s1]display sta-load-balance static-group all //查看静态负载均衡组的信息 [huawei-wlan-view]rrm-profile name r1 //创建RRM模板并进入模板视图 [huawei-wlan-rrm-prof-r1]sta-load-balance dynamic enable //使能动态负载均衡功能 [huawei-wlan-rrm-prof-r1]sta-load-balance dynamic start-threshold 10 //配置动态负载均衡的起始门限,缺省为10 [huawei-wlan-rrm-prof-r1]sta-load-balance dynamic gap-threshold 20 //配置动态负载均衡的差值门限,缺省为20% [huawei-wlan-rrm-prof-r1]sta-load-balance dynamic deny-threshold 3 //配置动态负载均衡拒绝终端关联最大次数,缺省为3次 [huawei]display rrm-profile name r1 //查看动态负载均衡的相关参数配置信息 [huawei]display radio-5g-profile name r5 //查看5G射频模板下的引用的RRM模板 [huawei]display station load-balance sta-mac 1000-0000-0000 //查看指定STA的动态负载均衡组信息 [huawei-wlan-view]rrm-profile name r1 //创建RRM模板并进入模板视图 [huawei-wlan-rrm-prof-r1]band-steer client-band-expire 35 //配置终端支持频段信息老化条件,缺省为AP连续只在同一频段收到终端的Probe帧次数超过35次 [huawei-wlan-rrm-prof-r1]smart-roam enable //使能智能漫游功能 [huawei-wlan-rrm-prof-r1]smart-roam roam-threshold check-rate //配置智能漫游的用户漫游触发方式,缺省为check-snr(信噪比) [huawei-wlan-rrm-prof-r1]smart-roam roam-threshold check-snr [huawei-wlan-rrm-prof-r1]smart-roam roam-threshold snr 20 //配置智能漫游的用户漫游门限值,缺省基于信噪比的门限值为20dB，基于终端速率的门限值为20% [huawei-wlan-rrm-prof-r1]smart-roam roam-threshold rate 20 [huawei-wlan-rrm-prof-r1]smart-roam quick-kickoff-threshold snr 15 //配置智能漫游的快速强制用户下线门限值,通过强制用户下线，可使得STA重新关联或者漫游到信号更好的AP上,缺省基于信噪比的门限值为15dB，基于终端速率的门限值为20%。 [huawei-wlan-rrm-prof-r1]smart-roam quick-kickoff-threshold rate 20 [huawei-wlan-rrm-prof-r1]smart-roam snr-margin high-level-margin 15 low-level-margin 6 //配置触发终端主动漫游切换的差值门限,缺省高差值门限为15dB，低差值门限为6dB [huawei-wlan-rrm-prof-r1]smart-roam snr-check-interval 3 //配置终端SNR的检测周期,缺省为3秒 [huawei-wlan-rrm-prof-r1]smart-roam unable-roam-client expire-time 120 //配置终端“不可切换”记录的老化时间,缺省为120分钟 [huawei-wlan-rrm-prof-r1]uac client-number enable //使能基于用户数的CAC功能 [huawei-wlan-rrm-prof-r1]uac client-number threshold access 64 //配置基于用户数的CAC门限, 缺省接入门限为64，漫游门限为64 [huawei-wlan-rrm-prof-r1]uac channel-utilization enable //使能基于信道利用率的CAC功能 [huawei-wlan-rrm-prof-r1]uac channel-utilization threshold access 80 //配置基于信道利用率的CAC门限, 缺省接入门限为80%，漫游门限为80% [huawei-wlan-rrm-prof-r1]uac client-snr enable //使能基于终端信噪比的CAC功能 [huawei-wlan-rrm-prof-r1]uac client-snr threshold 20 //配置基于终端信噪比的CAC门限, 缺省为20dB [huawei-wlan-rrm-prof-r1]uac reach-access-threshold hide-ssid //配置达到新增用户门限值时，隐藏SSID [huawei-wlan-rrm-prof-r1]dynamic-edca enable //使能动态EDCA参数调整 [huawei-wlan-view]radio-5g-profile name r5 //进入5G射频模板视图 [huawei-wlan-radio-5g-prof-r5]power auto-adjust enable //使能AP的逐包功率调整功能 [huawei-wlan-radio-5g-prof-r5]smart-antenna enable //开启AP的智能天线功能 [huawei]display wlan calibrate statistics ap-id 0 radio 0 //查看射频调优功能的统计信息 [huawei]reset wlan calibrate statistics ap-id 0 radio 0 //清除射频调优功能的统计信息 [huawei]display station smart-roam unable-roam //查看STA“不可切换”记录