注塑行业术语(中英文对照) | 您所在的位置:网站首页 › 行程英文单词缩写是什么 › 注塑行业术语(中英文对照) |
注塑行业术语(中英文对照) 注塑机参数 Injection Machine Parameter 1、注塑机规格参数 Injection Machine Specification 锁紧类型 clamp type 油缸 hydraulic 肘杆式 toggle 垂直注塑机导柱间距 tie bar verticalclearance 水平注塑机导柱间距 tie barhorizontal clearance 台板尺寸 platen dim. 最小 / 最大模厚 mold height Min./ Max., Min. / Max. mold thickness 最小 / 最大注塑机开档 open daylightMin. / Max. 锁紧行程 clamp stroke 锁紧力 clamping force 顶出行程 ejector stroke 顶出力 ejector force
2、试模工艺参数 Moulding Process Parameter, machine setting ①时间 Timer(TM ), sec 注塑(充填)时间 filling time,injection time 冷却时间 cooling time 补缩时间 packing time 保压时间 holding time- 成型周期 cycle time
②速率、速度 Velocity, %、speed, in/sec 注塑(充填)速度 injection speed 保压速率 hold pressurevelocity 螺杆转速 screw rotationspeed
③压力 Pressure(Prs. ), psi 注塑压力 injection pressure 保压压力 hold pressure 回压(背压) back pressure
④温度 Temperature(Temp. ), °F 注塑机喷嘴温度 nozzle temp 料筒前段、中段、后段温度 barrel front、middle、 rear temp 模温 mould temp 料温 purged resinmelt temp 空射料温 air shot melt temp
3、产品几何 Geometry 点 point 线(边) line, edge 面 face 侧面 side 表面 surface 外观面 appearance surface 壁厚 wall thickness, stock thickness 加强筋(骨位) rib 孔 hole 细长的槽 slot 柱位 boss 角 corner 圆角 fillet 倒角 chamfer 尖角 sharp corner 斜度 angle, taper 凹槽 recess , groove
一.分模信息 Splitting 分型线 parting line (P/L), splitting line 主分模方向 main direction, line of draw 浇口设定 gating
二.产品标识 Part Identification 产品名称 part name (P/N) 产品编号+版本号 part number + revision (Rev.) 型腔号 cavity number 材料标记 material symbol 模具编号 mold number (no.) 日期印 dating insert, date code 循环印 cycling code 公司标志 company logo
三.技术要求 Specification (SpecialRequirement) ①项目启动表 Kick-off sheet 项目名称 program name, project name 产品名称 part name, product name, partdescription 产品编号 part number (P/N) 客户模号 customer mold no. 项目启动日期 kick off date, start date 项目完成日期 due date, lead time 内模件用钢 tool steel 型腔数量 number of cavities 数据文件编号 data file no. 注塑材料 resin, plastic, raw material 收缩率 shrink, shrinkage, shrink factor 注塑机吨位 molding machine size, injectionmachine size 成型周期 cycle time 型腔光洁度 cavity polish 型芯光洁度 core polish 皮纹(晒纹) texture, grain 拔模斜度 draft angle, removal taper 注塑件颜色及光泽 molded color & gloss 模具加工地 manufacturing facility 热流道供应商 manifold manufacturer, manifoldsupplier 浇口位置 gate location / position 浇口类型 gate type 产品标识 stamp information, partidentification 特殊要求 special instructions
② 产品质量及外观要求 Part Quality & Appearance Requirement 1) 尺寸及公差 Dimension & Tolerance 重要尺寸 critical dimension, important dim., key dim. 理论尺寸 nominal dimension 实际尺寸 actual dimension 公差 tolerance 公差带 tolerance range 尺寸超差 dimension deviation 接受(合格) accept, OK 拒绝(不合格) reject, refuse, obsolete, NG 让步接受 concession, special admit 返工 re-work
2) 产品缺陷(常见的)Defects (normal) 缩水 sink mark, shrinkage 飞边,毛边 flash, burr 段差 mismatch discrepancy 银丝纹,蛇纹 snake marks, streak 弯曲,变形 warpage, distortion 打不饱(缺料) short shot 熔接线 weld line 多胶 unwanted plastic 拉伤 damage
③产品外观 Part Appearance 产品颜色 part color 产品光泽 gloss 皮纹粒度 grain
④常用词汇、词组及短语 Normal Word, Short Sentence 单边 per side 双边 both sides 加入,添加 add, incorporate 去除,取消 remove, cancel 满足…的要求,符合,与…要求一致 according to, conform to, satisfy, meet 要求,需要 require, need, demand 确认 be approved, agreed by … 允许 permit, allow 在…范围之内 Within 不可以,不允许,禁止 free from, prevent, avoid …,除非有另指 … unless otherwise specified …或少于 … or less 自动化运作 automatic operation 未注尺寸(详细形状)见三维造型 Non dimensioned contour(detailed shape) see 3D model. 分型线上的飞边(披缝)或段差应小于… Burrs or discrepancy onthe P/L shall be … or less.
四、标题栏 Title Block产品名称 — part name 图纸编号 + 版本号(索引号) drawing no. + level (index) 一般公差 general tolerance
苏州善德宸信贸易有限公司,SABIC一级代理商,致力于为汽车、消费电子和医疗等行业的客户,提供一流的工程塑料产品,和优质的技术和售后服务,欢迎来电咨询 。
|
CopyRight 2018-2019 实验室设备网 版权所有 |